Linksys WAP1200AC AC1200 Wi-Fi Access Point

Name: Linksys WAP1200AC AC1200 Wi-Fi Access Point
Brand: Linksys
SKU: CityCenter_5115
Price: 70 JOD
Availability: OutOfStock

The Linksys WAP1200AC AC1200 Wi-Fi Access Point is the latest in the AC-series access points, which utilizes the Cross Band technology. It can be used as a Wireless Range Extender or a Wired Access Point. Both functions maximize simultaneous use of the 2.4 GHz and 5 GHz bands for high-speed data transfer, uninterrupted streaming, and gaming. With the Linksys WAP1200AC, you can have video conference and share files without interruption, even when the rest of your family is gaming and streaming videos.

Not yet rated Write a review

Availability:: Out Of Stock
Product Code:: WAP1200AC
Brand:: Linksys

JOD 70.00

Chat with us on Whatsapp

Free delivery on orders Over 100 JOD
Cash on Delivery

Add to Wish List

Compare this Product

Front Panel

Antenna positioning is done depending on the type of home you have.

IMPORTANT: The antennas are fixed and can ONLY rotate at 180 degrees. Do NOT force the antennas too far back, otherwise, they will break.

For Single-story homes - Both antennas should be pointing down.

NOTE: For illustration purposes, the Linksys RE6700 is used in this example.

For Multi-story homes - One (1) antenna should always be pointing down to provide coverage for the current floor. The second antenna (any antenna) should be positioned differently depending on where the Linksys WAP1200AC is located and where the coverage is needed.

NOTE: For the most part, position one (1) antenna at 45 degrees as shown in Position A below. If there are issues with coverage, move the antenna at about 50-55 degrees down as shown in PositionB.

Position A can be used if the Linksys WAP1200AC is in the middle of the house.

Position B can be used if the Linksys WAP1200AC is connected to an outlet located at the farther side of the house.

Side Panel

Wi-Fi Protected Setup™ (WPS) button – Uses the WPS technology to automatically and securely add wireless devices to your network.

Reset button – Press and hold for 10 seconds to reset the Linksys WAP1200AC to factory default settings.

Bottom Panel

ETHERNET port – Connect an Ethernet-enabled device to the network using either a Cat 5 or 6 Ethernet cable.

Product Features

Concurrent dual-band (2.4 GHz and 5 GHz)
802.11ac Wireless technology
Compatible with 802.11 a/b/g/n
Data Rate of up to 300 Mbps for 2.4 GHz and up to 867 Mbps for 5 GHz
Two (2) external non-detachable antennas
2 x 2 Spatial Streams
One (1) 10/100/1000 Fast Ethernet port with auto MDIX sensing
Spot Finder technology (on Range Extender Mode only)
Wi-Fi Protected Setup™ (WPS)
Browser-based Setup (BBS)
Cross Band technology (on Range Extender Mode only)
Beamforming technology

LED Behaviors

Power / WPS LED:

OFF – There is no power on the Linksys WAP1200AC.
Blinking Green / Yellow – The Linksys WAP1200AC is starting up, resetting to factory defaults, upgrading its firmware, or the WPS connection is in process.
Solid Green / Yellow – The Linksys WAP1200AC is ready to use.
Solid Amber / Red – There is a weak connection with the router.
NOTE: To fix this issue, unplug the Linksys WAP1200AC and move it closer to the router.
Blinking Amber / Red – The Linksys WAP1200AC is not connected to the router, or the WPS pairing failed.

NOTE: To fix this issue, make sure that your router has an active Internet connection and the Wi-Fi is turned ON. If the router is working fine, unplug the Linksys WAP1200AC then move it closer to the router. Plug it back in, wait for one (1) minute, and reconnect to your network.

Ethernet LED – It lights up solid Green when an Ethernet device is connected and active. It will blink when sending or receiving data over the Ethernet port.

Product Requirements

Wi-Fi enabled computers or mobile devices
AC power outlet
Ethernet router or switch with available RJ45 Ethernet port and RJ45 Cable for Access Point mode or wireless network for Range Extender mode
For browser configuration:
- Internet Explorer® 8 or higher
- Safari® 5.1 for Mac® or higher
- Google Chrome™ 25.0 or higher
- Firefox® 20 or higher